Sorry for the bump/necro. But I have this problem still and I can't seem to fix it. I've been browsing for over an hour - honestly. I didn't find a solution.
- I use Windows 10
- I have the problem where I can uncheck "read-only" but it is immediately reset afterwards
- I don't have the option to "unblock"
- I think I gave myself full access (not sure about this last one however - but I will need clearer explanation how to make sure I have this, not a computer scientist)
I think these are the important characteristics but feel free to ask more info if needed.
Greetings and thanks!
Read Only Error (Can't un-tick)
Forum rules
READ THE INSTALL GUIDE BEFORE YOU POST IN THIS SUBFORUM.
The stickies exist to handle common queries. Save our time and yours by reading them first.
Thank you.
READ THE INSTALL GUIDE BEFORE YOU POST IN THIS SUBFORUM.
The stickies exist to handle common queries. Save our time and yours by reading them first.
Thank you.
Ads
Re: Read Only Error (Can't un-tick)
Did you run powershell stuff mentioned here and there on this board?

- FeistyDeity
- Posts: 50
Re: Read Only Error (Can't un-tick)
I tried it - doesn't seem like it made a difference.
Just to make sure I did it right: I got the option to type in a few letters. Like Y for Yes and A for Yes To All. I typed A and hit enter.
Just to make sure I did it right: I got the option to type in a few letters. Like Y for Yes and A for Yes To All. I typed A and hit enter.
- FeistyDeity
- Posts: 50
Re: Read Only Error (Can't un-tick)
Okay, I hope this is extensive enough. 
EDIT: Also, apologize that my computer doesn't run in english - I am dutchspeaking.
1. This is the location of my map.

2. The RoRLauncher is in the map.

3. When I hit Properties of the map, Read-Only is marked.

4. I unmark it and hit OK.

5. Just proof of it doing it lol.

6. I missed a screen apparently, but anyway. When I let it finish and then close the window - and then check properties again. It resets every time.

7. I open PowerShell and enter the thing the thread told me to.

8. I change the name to match my folder name.

9. Hit enter. Get this message.

10. Hit enter again. This pops up - I assume this means it is applied.

Is further info needed?

EDIT: Also, apologize that my computer doesn't run in english - I am dutchspeaking.
1. This is the location of my map.

2. The RoRLauncher is in the map.

3. When I hit Properties of the map, Read-Only is marked.

4. I unmark it and hit OK.

5. Just proof of it doing it lol.

6. I missed a screen apparently, but anyway. When I let it finish and then close the window - and then check properties again. It resets every time.

7. I open PowerShell and enter the thing the thread told me to.

8. I change the name to match my folder name.

9. Hit enter. Get this message.

10. Hit enter again. This pops up - I assume this means it is applied.

Is further info needed?

Re: Read Only Error (Can't un-tick)
Feisty, ik stuur je even Mijn ts info denk dat ik je er morgenochtend wel doorheen kan helpen. Spreken we rond 1 uur af en dan join je mijn teamspeak
Nazgul.darkstarventrilo.com:11765
Pass: Nazgul (capital N)
Nazgul.darkstarventrilo.com:11765
Pass: Nazgul (capital N)
- FeistyDeity
- Posts: 50
Re: Read Only Error (Can't un-tick)
Tomorrow afternoon you mean? (yeah ofc I understood you but it's just to make sure potential other viewers understand me) 
It's just that I'm not at home then - tomorrow evening would work tho if that works for you as well.

It's just that I'm not at home then - tomorrow evening would work tho if that works for you as well.
Ads
Re: Read Only Error (Can't un-tick)
Jah das goed.. 7 uur? En die andere mogen het zelf oplossen doe het Alleen omdat je nl bent 

Who is online
Users browsing this forum: Google Adsense [Bot] and 3 guests